2023 Correct and Up-to-date Cisco 300-610 BrainDumps
Current 300-610 dumps Preparation through Our Practice Test
The Cisco 300-610 exam is a comprehensive assessment of the candidate's knowledge of data center infrastructure design. The exam covers a variety of topics, including data center infrastructure design, data center storage networking design, data center compute networking design, data center virtualization design, and data center automation design. The exam is designed to test the candidate's ability to design data center infrastructure that is scalable, efficient, and secure.
The Cisco 300-610 exam is an essential certification exam for anyone interested in designing Cisco Data Center Infrastructure. Passing this exam will not only increase your knowledge in this area but also give you a competitive edge in the job market. Therefore, if you are interested in becoming a Cisco Data Center Infrastructure expert, take the time to prepare thoroughly and take the exam confidently.
The exam will consist of multiple-choice and simulation questions and will test the candidate's understanding of network design principles, best practices, and technologies that are used in data center infrastructure. Candidates are expected to have a thorough understanding of various Cisco products, including the Cisco Nexus and Cisco UCS, and be able to design data center solutions using these technologies. This certification exam is suitable for IT professionals who have at least five years of experience in designing data center solutions and have the skills required to design complex data center infrastructure.
NEW QUESTION # 55
An engineer must design a DNS service available to multiple network zones as a shared service. The network zones are deployed as VRFs within the data center network and no firewall is available for communication between VRFs.
Which protocol is needed to implement the shared services?
- A. VXLAN
- B. BGP
- C. ISIS
- D. OSPF
Answer: A
NEW QUESTION # 56
Refer to the exhibit.
What must be the default gateway of the servers in EPG Web?
- A. NAT appliance
- B. subnet address of BD2
- C. subnet address of BD1
- D. subnet address of L3Out
Answer: A
NEW QUESTION # 57
What are two reasons to select OTV as the DCI solution to connect multisite topologies? (Choose two.)
- A. It constrains HSRP hello messages to each data center.
- B. It propagates hosts reachability without support of traffic flooding.
- C. It extends the spanning tree between data centers.
- D. Layer 3 failures do not propagate beyond the OTV edge device.
- E. It is an open standard.
Answer: C,D
NEW QUESTION # 58
An engineer must logically partition two Cisco Nexus 7000 Series Switches into two environments called Test_39919596 and Production_59423879. The environments must use only F2-Series line cards and be limited to a maximum of 265 port-channels. Which Cisco Nexus feature must be used?
- A. VRF
- B. vFC
- C. VDC
- D. vPC
Answer: A
NEW QUESTION # 59
Drag the requirements from the left onto the correct policy types on the right.
Answer:
Explanation:
NEW QUESTION # 60
An engineer designs a Cisco UCS solution that must provide guaranteed and deterministic bandwidth to a specific server in the environment. The solution must apply to network and storage traffic of C-Series and B-Series servers. Which solution should be included to meet these requirements?
- A. Pin the vNlCs and vHBAs of the service profile to dedicated server ports
- B. Pin the IOM ports of the service profile to dedicated server ports.
- C. Pin the server ports of the service profile to dedicates uplink ports.
- D. Pin the vNICs and the vHBAs of the service profile to dedicated uplink ports.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/2-2/b_UCSM_GUI_Configuration_Guide_2_2/b_UCSM_GUI_Configuration_Guide_2_2_chapter_010.html#concept_7DE33CE2E37A47C6992C012D51CA37D4
NEW QUESTION # 61
An engineer is implementing a storage area network where an NPV is used. The engineer notices that the servers in a storage farm are experiencing heavy traffic contention. The engineer needs to migrate traffic from heavily loaded server interfaces to interfaces with less load. When the new links are deployed, the existing traffic is not rebalanced as expected. Which feature must be used to meet these requirements?
- A. NPIV
- B. multiple VSAN support
- C. DVM
- D. disruptive load balancing
Answer: A
NEW QUESTION # 62
Refer to the exhibit.
What must be the default gateway of the servers in EPG Web?
- A. NAT appliance
- B. subnet address of BD2
- C. subnet address of BD1
- D. subnet address of L3Out
Answer: A
NEW QUESTION # 63
Drag and drop the configurations from the left onto the correct policies on the right.
Answer:
Explanation:
NEW QUESTION # 64
Refer to the exhibit.
A Cisco UCS chassis that has two IOMs is discovered. The chassis discovery policy creates a fabric port channel. What is the result of this policy?
- A. Cisco UCS Manager creates two separate fabric port channels.
- B. Each uplink that connects an IOM is configured as a discrete link.
- C. The port channel is disabled until an administrator enables it manually.
- D. Cisco UCS Manager creates a single fabric port channel.
Answer: A
NEW QUESTION # 65
Which two configurations are available by using a service profile template in Cisco UCS Manager? (Choose two.)
- A. target server
- B. ARP entries
- C. UUID assignment
- D. VXLAN membership
- E. number of vHBAs
Answer: C,E
Explanation:
Section: Automation Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/cli/config/guide/2-2/ b_UCSM_CLI_Configuration_Guide_2_2/b_UCSM_CLI_Configuration_Guide_2_2_chapter_0100000.html
NEW QUESTION # 66
An engineer must logically partition two Cisco Nexus 7000 Series Switches into two environments called Test_39919596 and Production_59423879. The environments must use only F2-Series line cards and be limited to a maximum of 265 port-channels. Which Cisco Nexus feature must be used?
- A. vFC
- B. vPC
- C. VRF
- D. VDC
Answer: D
NEW QUESTION # 67
A failure occurs on the network between two BFD and OSPF neighbors. Drag and drop the protocol actions from the left into the correct order on the right.
Answer:
Explanation:
NEW QUESTION # 68
A storage engineer requires a solution that achieves multiple paths between a server and storage array. The design must support complete traffic isolation and support a 50% growth in the next year. Which FCoE solution meets these requirements?
- A. at least two FC zone sets with multiple zones
- B. single switch with multiple links
- C. single VSAN across the fabric
- D. at least two VSANs across the fabric
Answer: D
NEW QUESTION # 69
Which factor determines the choice of platform designing a Cisco HyperFlex infrastructure to support computer-aided design applications?
- A. processor count
- B. network speed
- C. GPU support
- D. storage capacity
Answer: D
Explanation:
https://www.cisco.com/c/dam/en/us/products/collateral/hyperconverged-infrastructure/hyperflex-hx-series/whitepaper-c11-740243.pdf
https://www.cisco.com/c/dam/en/us/products/collateral/hyperconverged-infrastructure/hyperflex-hx-series/hx-220c-m5-specsheet.pdf
NEW QUESTION # 70
A customer requires a tool to manage Cisco network hardware. The solution must use secure communication using a secure network protocol, support the use of declarative language to manage the state of resources, and periodically pull changes to the controlled nodes. Which tool meets these requirements?
- A. SaltStack
- B. Nomir
- C. Ansible
- D. Puppet
Answer: D
NEW QUESTION # 71
Drag and drop the feature descriptions from the left onto the correct UCS Fabric Interconnect modes on the right.
Answer:
Explanation:
NEW QUESTION # 72
Drag and drop the SAN components from the left onto the correct design considerations on the right.
Answer:
Explanation:
NEW QUESTION # 73
A network architect proposes a distinct Fibre Channel fabric to be used for a Cisco UCS blade server that hosts critical applications. Which action should be implemented for the fibre Channel traffic from the vHBA of this service to pass through the I/O module in the Cisco chassis to a specified uplink Fibre Channel port?
- A. Enable persistent binding in the vHBA policy.
- B. Update the applled Fibre Channel adapter policy.
- C. Include a SAN pin group in the vHBA policy.
- D. Update the applled global QoS policy.
Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/Storage-Mgmt/3-2/b_UCSM_GUI_Storage_Management_Guide_3_2/b_UCSM_GUI_Storage_Management_Guide_3_2_chapter_0110.pdf
NEW QUESTION # 74
......
100% Reliable Microsoft 300-610 Exam Dumps Test Pdf Exam Material: https://passguide.dumpexams.com/300-610-vce-torrent.html